Setting up A Bathtub
Setting up A Bathtub
Blog Article
They are making a few great pointers relating to How to Install a Bathtub Yourself overall in the content below.
Setting up a bath tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging job. If the old bathtub is conveniently accessible, the project can move quickly; if you have to open a wall to get rid of the old bathtub and position the brand-new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make sure you have qualified on your own for the work and also fit trying it. Instead of employing a professional to take over a halfway-completed task, it is far better to think about employing one before you begin. Possibilities are you may need a specialist plumber to make tube connections.
This short article will certainly aid you set up a new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and also product checklist ought to comprise the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be rather troublesome as a result of the limited access that is frequently the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the level as well as changing the feet on the tub until the spirit level reviews degree.
To set up taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water and also inspect all joints and new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, repair the bath paneling as defined in the maker's instruction manual. Tiling and securing around the tub should wait till the tub has been made use of a minimum of once as this will certainly settle it into its last setting.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type must be connected to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, causing difficulties with wetness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the market. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that article on Tools You Need to Install a New Bathtub from someone on another web property. Are you aware of another person who is excited by the niche? Why not promote it. Thanks for taking the time to read it.
Visit My Site
Report this page